Kugelhalterung für Yellow Diving Lampenkopf Video ( unsere Art.Nr. HEAD LV80) Zur Befestigung des Lampenkopfes an Video- Kugelgelenkarmen

Yellow Diving E/O Cord Kabel 5,8 - neue Ausführung mit angepresster Riffelung hinter dem Stecker. 1m

Yellow Diving E/O Cord Kabel 9,6 - neue Ausführung mit angepresster Riffelung hinter dem Stecker. 1m

E/O Y Connector Zur Verteilung von einem auf zwei Kabel

E/O Blindstecker zur Verwendung als "Schutzkappe"am Anzugkabel wenn das Kabel nicht benötigt wird

Ersatz O-Ring für Yellow Diving Akkutank O-Ring für die Abdichtung zwischen Tankdeckel und Tank.YD Akkutank H10 und H16  --- Durchmesser 75 mm , Länge 240 / 310 mm YD Akkutank H21 und H27 --- Durchmesser 80 mm , Länge 300 mmYD Akkutank H41               --- Durchmesser 90 mm , Länge 305 mm

Ersatzteil Schalter mit roter LED Yellow Diving, nur für Tanks ab Bj. 08/2024 !Der Schalter passt nicht für ältere Akkutanks !Ein Aufrüsten älterer Akkutanks mit diesem Schalter ist nicht möglich ! Lieferumfang: 1 Stück Kippschalter mit LED Lieferumfang nur der Schalter, Schalterkappe bitte bei Bedarf einzeln dazu bestellen. Es passen nur die Originalen YD Schalterkappen rot ! Der Schalter ist nur in Verbindung mit der Schalterkappe Wasserdicht ! Die Schalterkappe kann verschleißen, wir empfehlen eine Ersatzkappe auf Tauchausflügen dabei zu haben. Die Kabel müssen am Schalter angelötet werden. Wer sich das nicht zutraut kann Reparaturen gern bei uns anfragen.

Ersatzteil Schalter Yellow Diving, Lieferumfang: 1 Stück Kippschalter Lieferumfang nur der Schalter, Schalterkappe bitte bei Bedarf einzeln dazu bestellen. Es passen nur die Originalen YD Schalterkappen ! Der Schalter ist nur in Verbindung mit der Schalterkappe Wasserdicht ! Die Schalterkappe kann verschleißen, wir empfehlen eine Ersatzkappe auf Tauchausflügen dabei zu haben. Die Kabel müssen am Schalter angelötet werden. Wer sich das nicht zutraut kann Reparaturen gern bei uns anfragen.

Ersatzteil Schalterkappe rot Yellow Diving, paasend zu den Tank´s mit LED-Schalter ab Baujahr 08/2024 !!! Nur für YD Kippschalter passend !Lieferumfang : 1 Stück Schalterkappe rot Die Schalterkappe kann verschleißen, wir empfehlen eine Ersatzkappe auf Tauchausflügen dabei zu haben.

Ersatzteil: Schalterkappe Yellow Diving Nur für YD Kippschalter passend !

Halter für HID und LED Lampenköpfe zur Nutzung am ScooterBracket for mounting HID light heads series PERCH, M, L, S and V on the scooter body. Revolving to set correct angle of light beam. Eliminates a need of holding light head in hand. Suitable for any scooter.

LED Akkutanklampe 10 W,Kippschalter, SMALL & HANDY                                                      Canister - L 24cm / Ø 6cm                           Head - L 10,5cm / Ø 5,3cm L10 (Classic) - 10Watt 1050 lumens, Light-Emitting Diode (LED) primary lights are designed with fixed-focus light head and Li-Ion battery packs, available in the capacity range 5,2Ah. Used water-tight switch on/off with rubber cap.   The color temperature is about 6500°K, giving a light blue beam. Visibility of the spot is better even in shallow waters full of sunlight, making light communication between divers possible even in these conditions.The main feature of the head with a fixed focal length is concentrated (8°) beam of light with a distinct glow. All the electronics is located inside the light head, what allowed to manufacture shorter canister and gives possibility to use the same battery canister as power supply for light heads and electric heating Yellow Diving series.The goodman's handle is wide enough to be used in cold water with dry gloves. Threads of the height regulation screws are enforced now to avoid corrosion in salt water. Bungy line supplements the handle to allow easy changing of light-head hold while scootering.There is an eye-shaped piece of bungy line secured to the rotating ring located under the sealing gland, allowing to use a double ended bolt snap without a need of mounting it on the cable. When not in use, the light head could be temporarily attached to chest D-ring, with light beam directed downwards, without giving a dazzle. This way you can free your hands still having a dive light. Using attachments located on a goodman handle and bungy eye on rotating ring below sealing gland you can place your double ended bolt snap inside the contour of the light head, what is very useful when diving with reels and guidelines.Banana connectors between battery pack and canister cover makes storing canister and preparing for diving easier. When canister cover is put in-place, the power supply is connected in easy way. The cover could placed in two different positions – connected and not connected, what allow to secure the equipment during transport. This type of connections makes battery pack full water-tight up to 150m (450 fsw).   The battery indicator shows the level of the battery charge.Labelled "LED indicator", The LED indicator is located on the rightside of the head.The LED light indicates the battery performance status and providesinformation on the current battery level. When the battery is switched on, the indicator lights in one of thefollowing modes: green, continuous: 100 % – 16 % of charge capacityred, continuous: 15 % - 6 %red, intermittent: 5% – 0,1 %   TECHNICAL SPECIFICATIONS: - fixed focus 8°- colour temperature: 6500°K- luminance: 1050lm- complete electronics in headlamp- completely sealed Li-Ion battery pack- over-charge, over-discharge, over-drain and short circuits protection- banana connectors- battery indicator- classic rubber cap switch- standard cable length 1,0m long (or according to customer's order)- head length: 10,5cm- material: Delrin- max. operating depth: 150m- automatic charger for Li-Ion packs      Model Capacity - Ah Operating time – min Canister - L / Ø - cm Weight/ Weight in water - kg Charging time – h L1005 5,2 300 24 / 6 2,3 / 0,6 2            

L20 (Classic) - 20Watt 1700 lumens, Light-Emitting Diode (LED) primary lights are designed with fixed-focus light head and Li-Ion battery packs, available in the capacity range from 10,4Ah to 27,2Ah. Used water-tight switch on/off with rubber cap.The color temperature is about 6500°K, giving a light blue beam. Visibility of the spot is better even in shallow waters full of sunlight, making light communication between divers possible even in these conditions.The main feature of the head with a fixed focal length is concentrated (10 °) beam of light with a distinct glow.All the electronics is located inside the light head, what allowed to manufacture shorter canister and gives possibility to use the same battery canister as power supply for light heads and electric heating Yellow Diving series.The goodman's handle is wide enough to be used in cold water with dry gloves. Threads of the height regulation screws are enforced now to avoid corrosion in salt water. Bungy line supplements the handle to allow easy changing of light-head hold while scootering.There is an eye-shaped piece of bungy line secured to the rotating ring located under the sealing gland, allowing to use a double ended bolt snap without a need of mounting it on the cable. When not in use, the light head could be temporarily attached to chest D-ring, with light beam directed downwards, without giving a dazzle. This way you can free your hands still having a dive light. Using attachments located on a goodman handle and bungy eye on rotating ring below sealing gland you can place your double ended bolt snap inside the contour of the light head, what is very useful when diving with reels and guidelines.Banana connectors between battery pack and canister cover makes storing canister and preparing for diving easier. When canister cover is put in-place, the power supply is connected in easy way. The cover could placed in two different positions – connected and not connected, what allow to secure the equipment during transport. This type of connections makes battery pack full water-tight up to 150m (450 fsw).     TECHNICAL SPECIFICATIONS: - fixed focus 10°- colour temperature: 6500°K- luminance: 1700lm- complete electronics in headlamp- completely sealed Li-Ion battery pack- over-charge, over-discharge, over-drain and short circuits protection- banana connectors- classic rubber cap switch- standard cable length 1,0m* long (or according to customer's order)- head length: 10,5cm- material: Delrin- max. operating depth: 150m- automatic charger for Li-Ion packs   * option: E/O cord 1,0m (65cm/35cm) long (or according to customer's order)          Model Capacity - Ah Operating time – min Canister - L / Ø - cm Weight/ Weight in water - kg Charging time – h L2010 10,4 300 24 / 7,5 2,3 / 0,6 4  L2010 E/O 10,4 300 24 / 7,5 2,3 / 0,6 4  L2016 15,6 520 31 / 7,5 2,7 / 0,7 6 L2016 E/O 15,6 520 31 / 7,5 2,7 / 0,7 6 L2021 20,8 630 30 /  8 3,1 / 0,9 9 L2021 E/O 20,8 630 30 / 8 3,1 / 0,9 9 L2025 27,2 770 30 / 8 3,1 / 0,9 11 L2025 E/O 27,2 770 30 / 8 3,1 / 0,9 11

PERCH L20 (Piezo) - 20Watt 1700 lumens, Light-Emitting Diode (LED) primary lights are designed with fixed-focus light head and Li-Ion battery packs, available in the capacity range from 10,4Ah to 40,8Ah. Used water-tight piezo push-button switch.The color temperature is about 6500°K, giving a light blue beam. Visibility of the spot is better even in shallow waters full of sunlight, making light communication between divers possible even in these conditions.The main feature of the head with a fixed focal length is concentrated (10 °) beam of light with a distinct glow.All the electronics is located inside the light head, what allowed to manufacture shorter canister and gives possibility to use the same battery canister as power supply for light heads and electric heating Yellow Diving series.The goodman's handle is wide enough to be used in cold water with dry gloves. Threads of the height regulation screws are enforced now to avoid corrosion in salt water. Bungy line supplements the handle to allow easy changing of light-head hold while scootering.There is an eye-shaped piece of bungy line secured to the rotating ring located under the sealing gland, allowing to use a double ended bolt snap without a need of mounting it on the cable. When not in use, the light head could be temporarily attached to chest D-ring, with light beam directed downwards, without giving a dazzle. This way you can free your hands still having a dive light. Using attachments located on a goodman handle and bungy eye on rotating ring below sealing gland you can place your double ended bolt snap inside the contour of the light head, what is very useful when diving with reels and guidelines.Banana connectors between battery pack and canister cover makes storing canister and preparing for diving easier. When canister cover is put in-place, the power supply is connected in easy way. The cover could placed in two different positions – connected and not connected, what allow to secure the equipment during transport. This type of connections makes battery pack full water-tight up to 150m (450 fsw).

LH20 (Classic) primary diving light series with Light-Emitting Diode (LED) lighting technology 20Watt 1700 lumens  are designed with fixed-focus light head, additional on/off switch and  heating supply E/O cable and Li-Ion battery pack available in the capacity range from 20,8Ah to 27,2Ah. Used water-tight switch on/off with rubber cap. Cechą charakterystyczną głowicy reflektora o zmiennej ogniskowej jest poświata, jaką daje reflektor, gdy skupimy światło. All the electronics is now located inside the light head, what allowed to manufacture shorter  canister and gives possibility to use the same battery canister as power supply for light heads YD series and electric heating.Goodman handle is wide enough to use with dry gloves in cold waters. Threads of the height regulation screws are enforced now to avoid corrosion in salt water. Bungy line supplements the handle to allow easy changing of light-head hold while scootering.There is an eye-shaped piece of bungy line secured to the rotating ring located under the sealing gland, allowing to use a double-ender bolt-snap without a need of mounting it on the cable.  When not in use, the light head could be temporarily attached to chest D-ring, with light beam directed downwards, without giving a dazzle. This way you can free your hands still having a dive light. Using attachments located on a goodman handle and bungy eye on rotating ring below sealing gland you can place your double-ender bolt snap inside the contour of the light head, what is very useful when diving with reels and guidelines.Connectors between battery pack and canister cover makes storing canister and preparing for diving easier. When canister cover is put in-place, the power supply is connected in easy way.  The battery charger cable has long connectors with moving funnel covering the metal connector, what avoids short-circuit when connecting a charger. The cover could placed in two different positions – connected and not connected, what allow to secure the equipment during transport.  This type of connections makes battery pack full water-tight up to 150m. (450 fsw.)   TECHNICAL SPECIFICATIONS: - fixed focus - colour temperature: 6500°K- luminance: 1700lm- complete electronics in headlamp- completely sealed Li-Ion battery pack- over-charge, over-discharge, over-drain and short circuits protection- banana connectors- classic rubber cap switch- standard cable length 1,0m* long (or according to customer's order)- heating cable length: 65cm ( or according to customer’s order max. 1m)- head length: 16,7cm- material: Delrin- max. operating depth: 150m- automatic charger for Li-Ion packs 

PERCH LH20 (Piezo) primary diving light series with Light-Emitting Diode (LED) lighting technology 20Watt 1700 lumens  are designed with fixed-focus light head, additional on/off switch and  heating supply E/O cable and Li-Ion battery pack available in the capacity range from 20,8Ah to 27,2Ah. Used water-tight piezo push-button switch. Cechą charakterystyczną głowicy reflektora o zmiennej ogniskowej jest poświata, jaką daje reflektor, gdy skupimy światło. All the electronics is now located inside the light head, what allowed to manufacture shorter  canister and gives possibility to use the same battery canister as power supply for light heads YD series and electric heating.Goodman handle is wide enough to use with dry gloves in cold waters. Threads of the height regulation screws are enforced now to avoid corrosion in salt water. Bungy line supplements the handle to allow easy changing of light-head hold while scootering.There is an eye-shaped piece of bungy line secured to the rotating ring located under the sealing gland, allowing to use a double-ender bolt-snap without a need of mounting it on the cable.  When not in use, the light head could be temporarily attached to chest D-ring, with light beam directed downwards, without giving a dazzle. This way you can free your hands still having a dive light. Using attachments located on a goodman handle and bungy eye on rotating ring below sealing gland you can place your double-ender bolt snap inside the contour of the light head, what is very useful when diving with reels and guidelines.Connectors between battery pack and canister cover makes storing canister and preparing for diving easier. When canister cover is put in-place, the power supply is connected in easy way.  The battery charger cable has long connectors with moving funnel covering the metal connector, what avoids short-circuit when connecting a charger. The cover could placed in two different positions – connected and not connected, what allow to secure the equipment during transport.  This type of connections makes battery pack full water-tight up to 150m. (450 fsw.)   TECHNICAL SPECIFICATIONS: - fixed focus - colour temperature: 6500°K- luminance: 1700lm- complete electronics in headlamp- completely sealed Li-Ion battery pack- over-charge, over-discharge, over-drain and short circuits protection- banana connectors- classic rubber cap switch- standard cable length 1,0m* long (or according to customer's order)- heating cable length: 65cm ( or according to customer’s order max. 1m)- head length: 10,5cm- material: Delrin- max. operating depth: 150m- automatic charger for Li-Ion packs * option: E/O cord 1,0m (65cm/35cm) long (or according to customer's order)                              Model Capacity - Ah Operating time – min Canister - L / Ø - cm Weight/ Weight in water - kg Charging time – h PERCH LH 2021 20,8 560 28 /  8 3,1 / 0,9 9 PERCH LH 2021 E/O 20,8 560 28 / 8 3,1 / 0,9 9 PERCH LH 2025 27,2 630 28 / 8 3,1 / 0,9 11 PERCH LH 2025 E/O 27,2 630 28 / 8 3,1 / 0,9 11

L40 (Classic) - 40Watt 3960 lumens, Light-Emitting Diode (LED) primary lights are designed with fixed-focus light head and Li-Ion battery packs, available in the capacity range from 15,6Ah to 40,8Ah. Used water-tight switch on/off with rubber cap.The color temperature is about 6500°K, giving a light blue beam. Visibility of the spot is better even in shallow waters full of sunlight, making light communication between divers possible even in these conditions.The main feature of the head with a fixed focal length is concentrated (12°) beam of light with a distinct glow.All the electronics is located inside the light head, what allowed to manufacture shorter canister and gives possibility to use the same battery canister as power supply for light heads and electric heating Yellow Diving series.The goodman's handle is wide enough to be used in cold water with dry gloves. Threads of the height regulation screws are enforced now to avoid corrosion in salt water. Bungy line supplements the handle to allow easy changing of light-head hold while scootering.There is an eye-shaped piece of bungy line secured to the rotating ring located under the sealing gland, allowing to use a double ended bolt snap without a need of mounting it on the cable. When not in use, the light head could be temporarily attached to chest D-ring, with light beam directed downwards, without giving a dazzle. This way you can free your hands still having a dive light. Using attachments located on a goodman handle and bungy eye on rotating ring below sealing gland you can place your double ended bolt snap inside the contour of the light head, what is very useful when diving with reels and guidelines.Banana connectors between battery pack and canister cover makes storing canister and preparing for diving easier. When canister cover is put in-place, the power supply is connected in easy way. The cover could placed in two different positions – connected and not connected, what allow to secure the equipment during transport. This type of connections makes battery pack full water-tight up to 150m (450 fsw).     TECHNICAL SPECIFICATIONS: - fixed focus 12°- colour temperature: 6500°K- luminance: 3960lm- complete electronics in headlamp- completely sealed Li-Ion battery pack- over-charge, over-discharge, over-drain and short circuits protection- banana connectors- classic rubber cap switch- standard cable length 1,0m* long (or according to customer's order)- head length: 10,5cm- material: Delrin- max. operating depth: 150m- automatic charger for Li-Ion packs   * option: E/O cord 1,0m (65cm/35cm) long (or according to customer's order)          Model Capacity - Ah Operating time – min Canister - L / Ø - cm Weight/ Weight in water - kg Charging time – h              L4016 15,6 520 31 / 7,5 2,7 / 0,7 6 L4016 E/O 15,6 520 31 / 7,5 2,7 / 0,7 6 L4021 20,8 630 30 /  8 3,1 / 0,9 9 L4021 E/O 20,8 630 30 / 8 3,1 / 0,9 9 L4025 27,2 770 30 / 8 3,1 / 0,9 11 L4025 E/O 27,2 770 30 / 8 3,1 / 0,9 11

40-W-LED-Leuchte, 12°-Spot, Akkuladeanzeige, komplette Elektronik, Lichtschalter im Leuchtenkopf, 15,6-Ah-Li-Ion-Akku, Piezoschalter, blaue LED-Anzeige, 2 x E/O-Kabel (35/65 cm) Ladegerät   TECHNICAL SPECIFICATIONS: - fixed focus 12°- colour temperature: 6500°K- luminance: 3960lm- complete electronics in headlamp- completely sealed Li-Ion battery pack- over-charge, over-discharge, over-drain and short circuits protection- banana connectors- classic rubber cap switch- standard cable length 1,0m* long (or according to customer's order)- head length: 10,5cm- material: Delrin- max. operating depth: 150m- automatic charger for Li-Ion packs   * option: E/O cord 1,0m (65cm/35cm) long (or according to customer's order)

LH40 (Classic) primary diving light series with Light-Emitting Diode (LED) lighting technology 40Watt 3960 lumens  are designed with fixed-focus light head, additional on/off switch and  heating supply E/O cable and Li-Ion battery pack available in the capacity range from 20,8Ah to 40,8Ah. Used water-tight switch on/off with rubber cap. All the electronics is now located inside the light head, what allowed to manufacture shorter  canister and gives possibility to use the same battery canister as power supply for light heads YD series and electric heating.Goodman handle is wide enough to use with dry gloves in cold waters. Threads of the height regulation screws are enforced now to avoid corrosion in salt water. Bungy line supplements the handle to allow easy changing of light-head hold while scootering.There is an eye-shaped piece of bungy line secured to the rotating ring located under the sealing gland, allowing to use a double-ender bolt-snap without a need of mounting it on the cable.  When not in use, the light head could be temporarily attached to chest D-ring, with light beam directed downwards, without giving a dazzle. This way you can free your hands still having a dive light. Using attachments located on a goodman handle and bungy eye on rotating ring below sealing gland you can place your double-ender bolt snap inside the contour of the light head, what is very useful when diving with reels and guidelines.Connectors between battery pack and canister cover makes storing canister and preparing for diving easier. When canister cover is put in-place, the power supply is connected in easy way.  The battery charger cable has long connectors with moving funnel covering the metal connector, what avoids short-circuit when connecting a charger. The cover could placed in two different positions – connected and not connected, what allow to secure the equipment during transport.  This type of connections makes battery pack full water-tight up to 150m (450 fsw.)   The battery indicator shows the level of the battery charge.Labelled "LED indicator", The LED indicator is located on the rightside of the head.The LED light indicates the battery performance status and providesinformation on the current battery level.When the battery is switched on, the indicator lights in one of thefollowing modes:green, continuous: 100 % – 15 % of charge capacityred, continuous: 15 % - 5 %red, intermittent: 5% – 0,1 %   TECHNICAL SPECIFICATIONS: - fixed focus 12°- colour temperature: 3960°K- luminance: 1700lm- complete electronics in headlamp- completely sealed Li-Ion battery pack- over-charge, over-discharge, over-drain and short circuits protection- banana connectors- battery indicator- classic rubber cap switch- standard cable length 1,0m* long (or according to customer's order)- heating cable length: 65cm ( or according to customer’s order max. 1m)- head length: 10,5cm- material: Delrin- max. operating depth: 150m- automatic charger for Li-Ion packs   * option: E/O cord 1,0m (65cm/35cm) long (or according to customer's order)          Model Capacity - Ah Operating time – min Canister - L / Ø - cm Weight/ Weight in water - kg Charging time – h LH 4021 20,8 325 30 /  8 3,0 / 0,8 9 LH 4021 E/O 20,8 325 30 / 8 3,0 / 0,8 9 LH 4027 27,2 390 30 / 8 3,1 / 0,9 11 LH 4027 E/O 27,2 390 30 / 8 3,1 / 0,9 11 LH 4041 40,8  570 30,5 / 9 3,9 / 1 20 LH 4041 E/O 40,8 570  30,5 / 9 3,9 / 1 20

PERCH LH40 (Piezo) primary diving light series with Light-Emitting Diode (LED) lighting technology 40Watt 3960 lumens  are designed with fixed-focus light head, additional on/off switch and  heating supply E/O cable and Li-Ion battery pack available in the capacity range from 20,8Ah to 40,8Ah. Used water-tight piezo push-button switch. All the electronics is now located inside the light head, what allowed to manufacture shorter  canister and gives possibility to use the same battery canister as power supply for light heads YD series and electric heating.Goodman handle is wide enough to use with dry gloves in cold waters. Threads of the height regulation screws are enforced now to avoid corrosion in salt water. Bungy line supplements the handle to allow easy changing of light-head hold while scootering.There is an eye-shaped piece of bungy line secured to the rotating ring located under the sealing gland, allowing to use a double-ender bolt-snap without a need of mounting it on the cable.  When not in use, the light head could be temporarily attached to chest D-ring, with light beam directed downwards, without giving a dazzle. This way you can free your hands still having a dive light. Using attachments located on a goodman handle and bungy eye on rotating ring below sealing gland you can place your double-ender bolt snap inside the contour of the light head, what is very useful when diving with reels and guidelines.Connectors between battery pack and canister cover makes storing canister and preparing for diving easier. When canister cover is put in-place, the power supply is connected in easy way.  The battery charger cable has long connectors with moving funnel covering the metal connector, what avoids short-circuit when connecting a charger. The cover could placed in two different positions – connected and not connected, what allow to secure the equipment during transport.  This type of connections makes battery pack full water-tight up to 150m. (450 fsw.)   The battery indicator shows the level of the battery charge.Labelled "LED indicator", The LED indicator is located on the rightside of the head.The LED light indicates the battery performance status and providesinformation on the current battery level.When the battery is switched on, the indicator lights in one of thefollowing modes:green, continuous: 100 % – 15 % of charge capacityred, continuous: 15 % - 5 %red, intermittent: 5% – 0,1 % TECHNICAL SPECIFICATIONS: - fixed focus 12°- colour temperature: 6500°K- luminance: 3960lm- complete electronics in headlamp- completely sealed Li-Ion battery pack- over-charge, over-discharge, over-drain and short circuits protection- banana connectors- battery indicator- piezo push-button switch- standard cable length 1,0m* long (or according to customer's order)- heating cable length: 65cm ( or according to customer’s order max. 1m)- head length: 10,5cm- material: Delrin- max. operating depth: 150m- automatic charger for Li-Ion packs   * option: E/O cord 1,0m (65cm/35cm) long (or according to customer's order)          Model Capacity - Ah Operating time – min Canister - L / Ø - cm Weight/ Weight in water - kg Charging time – h PERCH LH 4021 20,8 325 30 /  8 3,0 / 0,8 9 PERCH LH 4021 E/O 20,8 325 30 / 8 3,0 / 0,8 9 PERCH LH 4027 27,2 390 30 / 8 3,1 / 0,9 11 PERCH LH 4027 E/O 27,2 390 30 / 8 3,1 / 0,9 11 PERCH LH 4041 40,8 570 30,5 / 9 3,9 / 1 20 PERCH LH 4041 E/O 40,8 570 30,5 / 9 3,9 / 1 20

75 Watt LED headlamp with the battery indicator. The LED light provides information on the current battery level. There are two independent LEDs module. E/O cord 35cm long   TECHNICAL SPECIFICATIONS: - 75 Watt- variable angle of light- battery indicator- angels of light indicator- color temperature: 6500°K- luminance 8000- E/O cord 35cm - complete electronics in headlamp- head length: 10,5cm The battery indicator shows the level of the battery charge.Labelled "LED indicator", The LED indicator is located on the rightside of the head.The LED light indicates the battery performance status and providesinformation on the current battery level. When the battery is switched on, the indicator lights in one of the following modes: green, continuous: 100 % – 16 % of charge capacityred, continuous: 15 % - 6 %red, intermittent: 5% – 0,1 %   There are two independent LEDs module."Angles of light" indicator shows a different angle of light beam.The indicator is located on the right side of the head.The modes lights work both together or separately.LED diode provides information on the current angle of light. It lights in one of the following modes: red - 35 Wattgreen - 40 Wattyellow- 75 Watt both channels of driver together NOT TO BE USED ON THE SURFACE   Time of work: L7516 (15,6 Ah) 35Watt 4:29 h 40Watt 3:51 h 75Watt 2:10 h   L7521 (20,8 Ah) 35Watt 6:41 h 40Watt 5:27 h 75Watt 2:50 h   L7525 (27,2 Ah) 35Watt 8:15 h 40Watt 6:31 h 75Watt 3:22 h   L7541 (41 Ah) 35Watt 12:25 h 40Watt 9:33 h 75Watt 4:50 h !!! You can switch between modes by useing switch on/off. When you turn the light off, you have 5 seconds to turn it on again then the mode changes. If you turn it off for longer period (more than 5 seconds), the light will work in it's first mode (35 Watt ) !!!

75 Watt LED headlamp with the battery indicator. The LED light provides information on the current battery level. There are two independent LEDs module. E/O cord 35cm long   TECHNICAL SPECIFICATIONS: - 75 Watt- variable angle of light- battery indicator- angels of light indicator- color temperature: 6500°K- luminance 8000- E/O cord 35cm - complete electronics in headlamp- head length: 10,5cm The battery indicator shows the level of the battery charge.Labelled "LED indicator", The LED indicator is located on the rightside of the head.The LED light indicates the battery performance status and providesinformation on the current battery level. When the battery is switched on, the indicator lights in one of the following modes: green, continuous: 100 % – 16 % of charge capacityred, continuous: 15 % - 6 %red, intermittent: 5% – 0,1 %   There are two independent LEDs module."Angles of light" indicator shows a different angle of light beam.The indicator is located on the right side of the head.The modes lights work both together or separately.LED diode provides information on the current angle of light. It lights in one of the following modes: red - 35 Wattgreen - 40 Wattyellow- 75 Watt both channels of driver together NOT TO BE USED ON THE SURFACE   Time of work: L7516 (15,6 Ah) 35Watt 4:29 h 40Watt 3:51 h 75Watt 2:10 h   L7521 (20,8 Ah) 35Watt 6:41 h 40Watt 5:27 h 75Watt 2:50 h   L7525 (27,2 Ah) 35Watt 8:15 h 40Watt 6:31 h 75Watt 3:22 h   L7541 (41 Ah) 35Watt 12:25 h 40Watt 9:33 h 75Watt 4:50 h !!! You can switch between modes by useing switch on/off. When you turn the light off, you have 5 seconds to turn it on again then the mode changes. If you turn it off for longer period (more than 5 seconds), the light will work in it's first mode (35 Watt ) !!!

LH75 (Classic) primary diving light series with Light-Emitting Diode (LED) lighting technology 35Watt/40Watt/75Watt, 3600lm/4400lm/8000lumens,  are designed with changeable focus light head 12°-120°, additional on/off switch and  heating supply E/O cable and Li-Ion battery pack available in the capacity range from 20,8Ah to 40,8Ah. Used water-tight switch on/off with rubber cap. All the electronics is now located inside the light head, what allowed to manufacture shorter  canister and gives possibility to use the same battery canister as power supply for light heads YD series and electric heating.Goodman handle is wide enough to use with dry gloves in cold waters. Threads of the height regulation screws are enforced now to avoid corrosion in salt water. Bungy line supplements the handle to allow easy changing of light-head hold while scootering.There is an eye-shaped piece of bungy line secured to the rotating ring located under the sealing gland, allowing to use a double-ender bolt-snap without a need of mounting it on the cable.  When not in use, the light head could be temporarily attached to chest D-ring, with light beam directed downwards, without giving a dazzle. This way you can free your hands still having a dive light. Using attachments located on a goodman handle and bungy eye on rotating ring below sealing gland you can place your double-ender bolt snap inside the contour of the light head, what is very useful when diving with reels and guidelines.Connectors between battery pack and canister cover makes storing canister and preparing for diving easier. When canister cover is put in-place, the power supply is connected in easy way.  The battery charger cable has long connectors with moving funnel covering the metal connector, what avoids short-circuit when connecting a charger. The cover could placed in two different positions – connected and not connected, what allow to secure the equipment during transport.  This type of connections makes battery pack full water-tight up to 150m (450 fsw.)   The battery indicator shows the level of the battery charge.Labelled "LED indicator", The LED indicator is located on the rightside of the head.The LED light indicates the battery performance status and providesinformation on the current battery level.When the battery is switched on, the indicator lights in one of thefollowing modes:green, continuous: 100 % – 15 % of charge capacityred, continuous: 15 % - 5 %red, intermittent: 5% – 0,1 % There are two independent LEDs module."Angles of light" indicator shows a different angle of light beam.The indicator is located on the right side of the head.The modes lights work both together or separately.LED diode provides information on the current angle of light.It lights in one of the following modes:green - 35 Watt/ 12°red - 40 Watt/ 120°yellow- 75 Watt both channels of driver together You can switch between modes by using switch on/off. When you turn the light off,you have 5 seconds to turn it on again then the mode changes. If you turn it off forlonger period (more than 5 seconds), the light will work in it's first mode (35 Watt,12°)   TECHNICAL SPECIFICATIONS: - light angle 12°/ 120°- colour temperature: 6500°K- luminance: max 8000lm- complete electronics in headlamp- completely sealed Li-Ion battery pack- over-charge, over-discharge, over-drain and short circuits protection- banana connectors- angels of light indicator- battery indicator- classic rubber cap switch- standard cable length 1,0m* long (or according to customer's order)- heating cable length: 65cm ( or according to customer’s order max. 1m)- head length: 10,5cm- material: Delrin- max. operating depth: 150m- automatic charger for Li-Ion packs   * option: E/O cord 1,0m (65cm/35cm) long (or according to customer's order)          Model Capacity - Ah Operating time – min Canister - L / Ø - cm Weight/ Weight in water - kg Charging time – h LH 7521 20,8 35W/ 400 40W/ 325 75W/ 170 30 /  8 3,0 / 0,8 9 LH 7521 E/O 20,8 35W/ 400 40W/ 325 75W/ 170 30 / 8 3,0 / 0,8 9 LH 7527 27,2 35W/ 495 40W/ 390 75W/ 200 30 / 8 3,1 / 0,9 11 LH 7527 E/O 27,2 35W/ 495 40W/ 390 75W/ 200 30 / 8 3,1 / 0,9 11 LH 7541 40,8 35W/ 745 40W/ 570 75W/ 290 30,5 / 9 3,9 / 1 20 LH 7541 E/O 40,8 35W/ 745 40W/ 570 75W/ 290 30,5 / 9 3,9 / 1 20

Li-Ion battery pack 15,6 AhErsatzakkupack in verschiedenen Kapazitäten passend  für Yellow Diving Akkutanks. Lieferumfang jeweils nur der Akkupack ! Bitte geben Sie uns zum Abgleich die Seriennummer Ihres Akkutanks an.15,6Ah 11,1V Li-Ion battery pack - over-charge, over-discharge, over-drain and short circuits protection - battery pack dimensions: height 19,8cm x diameter 5,8cm